4.9 ★On Google50+ locationsGA + FloridaOpen 7 daysEst. 2012 — Family owned
Pack of three VOOPOO TPP-DM1 0.15 ohm mesh coils

Cloud 9 guide

VooPoo TPP DM1 Guide: 0.15 Ohm Mesh Coil, 3-Pack

A guide to the VOOPOO TPP-DM1 0.15 ohm mesh coil 3-pack: 60 to 80W direct-lung range, the DM1 to DM4 lineup, TPP tank fit and priming steps.
Read the article

The VooPoo TPP DM1 0.15 ohm Coil 3-pack gives you three mesh coils for VOOPOO's TPP-series tanks and pods. VOOPOO rates the TPP-DM1 as a direct-lung (DL) coil at 60 to 80W, and it's one of four TPP coils, alongside the DM2, DM3 and DM4.

VOOPOO sums up the DM1 in two words, 'high sweetness.' It's a low-resistance, high-power coil built for a big, open pull, and with three in a pack you'll have backups ready when the first one wears out.

Who is the TPP DM1 for?

It's for anyone with a TPP-series tank, like VOOPOO's MAAT tank, who wants a high-power, direct-lung coil. Within the family, the DM2 (0.2 ohm, 40-60W) runs at lower power, the DM3 (0.15 ohm, 80-100W) runs even hotter, and the DM4 (0.3 ohm, 32-40W) is the gentlest. If your device uses plug-in PnP pods instead of a TPP tank, the PnP-VM6 or PnP X 0.15 ohm coils are the ones to look at.

TPP DM1 at a glance

VooPoo TPP-DM1 coil specifications
Feature Detail
Resistance 0.15 ohm
Listed wattage 60 to 80W
Heating element Mesh (VOOPOO describes Dual In One Tech 2.0 mesh for TPP coils)
Draw style Direct lung (DL)
Pack size 3 coils
VOOPOO's description High sweetness

Those details come from VOOPOO's MAAT tank page. That page isn't completely consistent about which coils it lists with the tank, but the DM1's numbers match everywhere they appear.

How do the DM1, DM2, DM3 and DM4 compare?

VOOPOO TPP coil family
Coil Style Resistance Listed power How VOOPOO describes it
TPP-DM1 Direct lung 0.15 ohm 60 to 80W High sweetness
TPP-DM2 Direct lung 0.2 ohm 40 to 60W Rich and dense
TPP-DM3 Direct lung 0.15 ohm 80 to 100W Boosting output
TPP-DM4 Half direct lung 0.3 ohm 32 to 40W Delicate and soft

The descriptions in the last column are VOOPOO's own words for each coil's character. This pack is all DM1. Notice that the DM1 and DM3 are both 0.15 ohm but rated for different power, which is why the coil code matters more than the resistance alone.

A quick word on the draw-style labels. Mouth to lung (MTL) is a slow, tight pull where the vapor gathers in your mouth first, and it goes with higher resistance and low wattage. Direct lung (DL) is a wide-open, straight-to-the-lungs pull that goes with low resistance and higher wattage. Restricted direct lung (RDL) sits in between. These labels describe airflow and coil design, not strength; the nicotine level of any e-liquid is printed on its own bottle.

What is the TPP DM1 compatible with?

VOOPOO's MAAT tank page lists the MAAT tank (26 by 52 mm, 510 base, 810 drip tip) with TPP coils, and says the ARGUS GT II works with all TPP coils. TPP coils come in several types, so check the code on the coil that's in your device now before you swap.

TPP coils are their own family. They aren't PnP or PnP X coils, even when the ohms and wattage match, and VOOPOO's PnP platform page doesn't include them. If you have a Drag or Vinci that uses PnP pods, look at the PnP coil lines instead.

How do you install and prime a TPP DM1 coil?

  1. Turn the device off and let it cool. Then take the tank or pod off.
  2. Remove the old coil. Pull or unscrew it the way your tank or pod is designed, and leave the O-rings and seals in place.
  3. Prime the new DM1. Drip a few drops of e-liquid into the cotton openings so the wick is wet before the first pull.
  4. Seat it firmly. Push the coil in until it's fully home, then put the tank or pod back together.
  5. Fill and wait. Fill up and give the cotton several minutes to soak before you power on.

Once it's primed, start near the low end of 60 to 80W and only work up once you're sure the cotton is fully soaked.

Mesh just means the heating element is a flat sheet of fine metal mesh instead of a round wire wrapped around the cotton. The sheet touches more of the wick at once, which is why mesh coils heat up quickly and evenly. The basics don't change, though: soak the cotton first, stay inside the printed wattage range and swap the coil once it starts tasting burnt.

Care and troubleshooting

Rinse the tank body and glass when you change e-liquids, but leave the coil dry. High-wattage coils work hard, so expect to replace them regularly, and swap it once the flavor fades or turns burnt.

If the flavor fades, you get a burnt taste or the device shows a coil error, start with the easy checks. Make sure the coil is seated all the way, the cotton had time to soak, and your wattage is inside the range VOOPOO lists for that coil. A dry hit usually means the wick wasn't fully soaked or the power is set too high. A coil that's been in a while and has picked up dark, sticky gunk from the e-liquid is simply worn out and ready to replace; sweet, thick e-liquids tend to gunk up coils sooner. If liquid is pooling or leaking, check the seals and how full the tank is before blaming the coil.

TPP DM1 FAQ

What resistance is the TPP DM1?

0.15 ohm, rated for 60 to 80W.

How many coils come in a pack?

Three.

Does it contain nicotine?

No. It's hardware.

Is the DM1 the same as the DM3?

No. Both are 0.15 ohm, but VOOPOO rates the DM1 for 60 to 80W and the DM3 for 80 to 100W.

Is the TPP DM1 coil at my local Cloud 9?

It varies by store. Use the Cloud 9 store locator to find your nearest shop, and call ahead to check on the DM1.

Where to find the VooPoo TPP DM1 coil near you

Cloud 9 Smoke Co. is a family-owned shop founded in 2012, with more than 50 locations across Georgia and Florida. Find your closest store with the Cloud 9 store locator, or browse our Georgia locations and Florida locations. Bring your device and the old part, or a photo of the code printed on it, and we'll match it up with you.

More guides you might like

For adults 21+.

Previous Next
Cloud 9 — Established 2012

You Must Be 21 Years or Older To View This Site

Are You 21+ Years Old?

By entering this site you are agreeing to the Terms of Use and Privacy Policy and you lawfully agree you are above the age of 21.