The Smok LP1 Meshed 5pk is a five-pack of mesh replacement coils from SMOK's LP1 series, and it comes in three resistances: 0.8, 0.9 and 1.2 ohm. SMOK lists LP1 coils for the Novo 4, the Novo 4 Mini and the Pozz Pro, so if you've got one of those kits, these are made for your pod.
The resistance is the main thing to pick. Lower and higher numbers are wired for different power levels and draws, and the right one comes down to your kit and how you like to vape. The number is printed right on the pack.
What resistances does the LP1 Meshed coil come in?
- 0.8 ohm is the lowest-resistance LP1 Meshed coil.
- 0.9 ohm is the mouth-to-lung (MTL) version, according to SMOK Store. SMOK also makes a Turbo Meshed 0.9 ohm MTL coil, so check which 0.9 you're holding.
- 1.2 ohm is the highest-resistance LP1 Meshed coil.
SMOK LP1 Meshed at a glance
| Spec | Detail |
|---|---|
| Series | SMOK LP1 |
| Heating element | Mesh |
| Pack size | 5 coils |
| Resistances | 0.8, 0.9 and 1.2 ohm |
| Fits | Novo 4, Novo 4 Mini, Pozz Pro |
What is a mesh coil?
Instead of a wire wound into a spiral, a mesh coil uses a flat sheet of metal mesh as the heating element. Manufacturers like it because it gives a bigger heating surface touching the cotton. Every LP1 coil except the dual-coil DC 0.8 MTL uses it.
Which devices do LP1 Meshed coils fit?
The SMOK compatibility guide lists LP1 coils for the Novo 4 kit, the Novo 4 Mini kit and the Pozz Pro kit. Here's the whole LP1 family so you can see where each one sits:
| Coil | Resistance | Style |
|---|---|---|
| LP1 DC MTL | 0.8 ohm | Dual coil, mouth-to-lung |
| LP1 Meshed | 0.8 ohm | Mesh |
| LP1 Meshed MTL | 0.9 ohm | Mesh, mouth-to-lung |
| LP1 Meshed MTL (Turbo Meshed) | 0.9 ohm | Mesh, mouth-to-lung, Turbo Meshed |
| LP1 Meshed | 1.2 ohm | Mesh |
The other option for the same kits is the dual-coil version, covered in our LP1 DC 0.8 MTL coil guide. LP2 coils are a different series for other kits and won't work in an LP1 pod. And if you're on a Novo 4 Mini, remember its pod is sold empty and the coil goes in separately, as our Novo 4 Mini pods guide explains.
How do you install a new LP1 coil?
- Prime the coil with a few drops of e-liquid on the exposed cotton.
- Push it into a compatible LP1 pod.
- Fill the pod and give it several minutes to soak before you use it.
- Swap it out when the flavor starts to weaken.
Keep spare coils in their packaging until you need them, away from heat, sun and moisture, and try not to touch the cotton with your fingers. When a coil's done, toss it with your small electronics and keep all your vape gear out of reach of kids and pets.
What if the draw or flavor changes?
Change one thing at a time. A new resistance, a new juice and a freshly primed coil can each change how a pod feels, so if you're troubleshooting, swap only the coil first. Weak flavor usually means an old coil. Gurgling or leaking is more often a pod that isn't seated right or has been overfilled. How long a coil lasts depends on your power setting, how much you vape and the liquid you use, and sweet, thick juices gunk up any coil faster.
SMOK LP1 Meshed FAQ
How many coils are in a pack?
Five.
Which devices use LP1 coils?
SMOK lists the Novo 4, Novo 4 Mini and Pozz Pro kits.
Which resistance should I pick?
Match the number on your old coil or the one your kit manual calls for. The resistance is printed on every pack.
Do they contain nicotine?
No. They're hardware.
Is every resistance at my local Cloud 9?
It varies by store. Use the Cloud 9 store locator and call ahead for a specific resistance.
Where to find the SMOK LP1 Meshed coils near you
Cloud 9 Smoke Co. is a family-owned shop founded in 2012, with more than 50 locations across Georgia and Florida. Find your closest store with the Cloud 9 store locator, or browse our Georgia locations and Florida locations. For spare pods, see the SMOK Novo 4 Mini pods guide.
For adults 21+.
